Loadinginstant700

Is therefore a genuine multi-protocol Digital system. It is extremely efficient and compact and brings many functions into a single box. The entire system in one box The Intellibox has on board all the functions which formerly had to be laboriously installed into the layout. Speed controller. Control System Driver Search We are continually updating our driver database. If you have a manufacturer or specific model request please contact your local support at 800.633.9876.

Software for device programmers

Elnec provides one common software for all device programmers. There are available regular version and OnDemand versions of software. Regular version is released normally every 3-4 weeks, OnDemand versions are released on demand - for hot new devices support and bugs fixes - often daily. For detailed description of control program for programmers look please at Software page.

Elnec software is in the form of installer, which copies control software for Elnec programmers to your hard disk, creates shortcuts in the start menu and associates project files with Elnec software, if desired.

The setup program must run with administrative rights, however Elnec software runs fine without administrative rights once it is installed.

Installation: To install Elnec software for programmers, run the PG4UWarc.EXE (or PG4UWarc-OnDemand.exe) file and follow the wizard.

Updating: Run the PG4UWarc.EXE (or PG4UWarc-OnDemand.exe) file. You do not need to uninstall the old version first. Your configuration options will not be lost.

Silent Installation: The PG4UWarc.EXE (and PG4UWarc-OnDemand.exe) installer supports command line switches for silent installation, i.e. the program gets installed without asking the user for target directory or association options. The default settings of the installer are used. The /SILENT command line switch performs a silent installation and shows a status dialog during the setup process. No questions will be asked though.

Uninstallation: In order to uninstall Elnec software for programmers, run the uninstallation program, which is accessible by a shortcut in the start menu folder of Elnec, or in the program section of the system control panel. If you also want to remove your configuration settings, you need to delete the configuration file in the application data directory of your user profile. The /SILENT command line switch can be used also here.

Important: The software package for BeeProg3 and BeeHive304 programmers contain also updates of firmware, libraries and operating system for these programmers, which mean (roughly) next 20MB of compressed data. In intent to save download time - and also in intent to save the disk space after installation of software - we come to conclusion to provide two installation packages:

• the first one: PG4UWarc.EXE (and PG4UWarc-OnDemand.exe) is for all Elnec programmers but doesn't include BeeProg3/BeeHive304 support.
• the second one: PG4UWarc3.EXE (and PG4UWarc3-OnDemand.exe) is for all Elnec programmers including BeeProg3/BeeHive304 support. This package is for users of BeeProg3 and BeeHive304 programmers.

Notes:

• The support of new devices implemented by OnDemand software is available for BeeProg3/BeeHive304, BeeHive208S/BeeHive204, BeeProg2/BeeProg2C/BeeProg+ and BeeHive204AP/BeeProg2AP programmers only
• The installation file (PG4UWarc.EXE and PG4UWarc-OnDemand.exe) may be keeped to reinstall SW in the future.

PC requirements

• For best performance we recommend 1024 x 768 or higher screen resolution.
• The 'Minimal PC requirements' mean, the device programmer and SW will run at these conditions, but not with fully enjoyable experience

Download Multi Protocol Programming System Driver Training

• These PC requirements are valid for 3.38 version of control program for programmers (issued 01.Feb.2018) and above.
• If two programmers are to be connected to a single PC, then we strongly recommend to connect each programmer to separate USB 2.0 High speed controller (USB EHCI). For more information see User manual for the programmer, the 'Hardware setup' chapter.
• Free disk space requirements depends also on used IC device size and number of attached programming sites. For large devices the required free space on disk will be approximately 1000MB+ 2x Device sizexnumber of programming sites attached to this PC.
• Very easy indication, if your PC in hardware/software configuration is good enough for the current software version and current situation with PG4UW/PG4UWMC, is to run Windows task manager (Ctrl+Alt+Del) and see the performance folder. It has to be max. 80% of CPU usage at full run of programming system.
• We still recommend Windows 7 because of unexpected restarts after automatic updates of the Windows 10. If you are fine with this, you can use Windows 10.

• for work with the actual version of SW the BeeHive208S programmers must have installed 2GB RAM or above.
• except the above RAM size increase, the PC inside of the all BeeHive208S programmers is still above the Minimal PC requirements for actual version of the software.

Manuals and other documents

You need to have PDF files. You can use Adobe Acrobat Reader.
But better might be Sumatra PDF - faster and smaller. Get Sumatra PDF

Unsupported products

Download Multi Protocol Programming System Driver Download

Note:

• DOS version of SW for programmers has been discontinued since 7/2003. The software will not work with programmers, manufactured after this date. We provide none support and none consultations regarding DOS version of SW for programmers.
• The version of SW can be used for MS-DOS OS, as well for WIN 3.xx, WIN95, WIN98/Me.

Download Multi Protocol Programming System Driver Updater